Routed OpenVPN between two subnets behind NAT gateways
categories:
- Networks
- Security
- VPN
Edit : between two or MORE subnets. Check out the exchange between Michael Antal and me in the comments. He’s been able to interconnect 3 subnets using this method and some slight tweaks in routes.
The following is the configuration needed to create a routed OpenVPN network between two remote subnets, both behind NAT gateways. On each side, the gateways will act as the VPN gateways.
Network subnets on both side must be different. In this example, we connect 192.168.1.0/24 to 192.168.200.0/24.
With this setup, we don’t even need to open ports at the NAT level on either side of the VPN.
Network configuration
Network A :
Subnet : 192.168.1.0/24
Gateway for Network A
VPN interface (tun0) : 10.0.0.1
Eth0 : 192.168.1.254
Eth1 / Public IP : 212.x.x.x (machineA.example.org)
Network B :
Subnet : 192.168.200.0/24
Gateway for Network B
VPN interface (tun0) : 10.0.0.2
Eth0 / Public IP : 66.x.x.x (machineB.example.org)
Eth1 : 192.168.200.254
If we imagine forwarding is rejected at the firewall level on machine B, we would need to allow traffic between the tun device created by OpenVPN and the LAN interface, as root you would then type :
iptables -I FORWARD -i tun0 -o eth1 -j ACCEPT
iptables -I FORWARD -i eth1 -o tun0 -j ACCEPT
Make sure the rules remain applied across reboots (using iptables-save or storing the rules in /etc/rc.local or else)
Enabling IP routing :
We need to enable routing on both VPN gateways..
echo "1" > /proc/sys/net/ipv4/ip_forward
Using this method, routing is not persistent across reboots, check the following link (which works for Debian as well)
Static key generation :
We will use simple static key for our example…
openvpn --genkey --secret /etc/openvpn/vpn.key
Share the key between the VPN gateways over a secure channel (scp, etc.).
If you want to use certificates instead (which I recommend), check out : http://blog.wains.be/post/a-vpn-for-remote-users-with-openvpn/
OpenVPN configuration :
machine A : /etc/openvpn/vpn.conf
remote machineB.example.org
float
port 8000
dev tun
ifconfig 10.0.0.1 10.0.0.2
persist-tun
persist-local-ip
persist-remote-ip
comp-lzo
ping 15
secret /etc/openvpn/vpn.key
route 192.168.200.0 255.255.255.0
chroot /var/empty
user nobody
group nogroup
# If using Red Hat replace with
# group nobody
log vpn.log
verb 1
machine B : /etc/openvpn/vpn.conf
remote machineA.example.org
float
port 8000
dev tun
ifconfig 10.0.0.2 10.0.0.1
persist-tun
persist-local-ip
persist-remote-ip
comp-lzo
ping 15
secret /etc/openvpn/vpn.key
route 192.168.1.0 255.255.255.0
chroot /var/empty
user nobody
group nogroup
# If using Red Hat replace with
# group nobody
log vpn.log
verb 1
Establishing the connection :
On machine A type :
openvpn --config /etc/openvpn/vpn.conf
Machine A will try to establish the connection. Type the same command on machine B to initialize the connection.
As soon as the connection is up, hosts on network A should be able to ping hosts on network B and vice-versa. If you can’t ping from one side to the other, it’s probably a routing issue.
We can use traceroute from a machine on network A to see the path taken to reach a host on network B :
$ traceroute 192.168.200.30 traceroute to 192.168.200.30 (192.168.200.30), 30 hops max, 40 byte packets 1 192.168.1.254 (192.168.1.254) 2.128 ms 2.378 ms 2.781 ms 2 10.0.0.2 (10.0.0.2) 132.761 ms 137.342 ms 141.130 ms 3 192.168.200.30 (192.168.200.30) 136.752 ms 133.869 ms 135.960 ms
We can see the traffic is going through the 10.0.0.2 interface.
We also can check the routing table on the VPN gateway on network A :
# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.200.0 10.0.0.2 255.255.255.0 UG 0 0 0 tun0 0.0.0.0 212.x.x.x 0.0.0.0 UG 0 0 0 eth1
We see any traffic directed to 192.168.200.0/255.255.255.0 must go through interface 10.0.0.2 on device tun0.
Making sure the VPN connection is established at boot (Debian way) :
Edit /etc/defaults/openvpn and specify which VPN network must be started.
Make OpenVPN starts at boot with this command :
update-rc.d openvpn defaults
OpenVPN will start any VPN configuration named *.conf found in /etc/openvpn/ So don’t store copies of config like test.conf test-backup.conf as OpenVPN will try to start them at boot.